Post by ventura7211 on Dec 18, 2006 13:10:05 GMT -6
SBC
2 350 2 bolt blocks $100 apiece or $175 for both
1 350 2 bolt short block $150
1 350 4 bolt short block 1 piece rear main $225
1 350 4 bolt block $150
BBC
396 block $200
Several sets of heads $75 a pair
Gen V 454 Forged Steel crank, 6 7/16" dimple rods
the crank is std and will probably need turned as one journal is discolored and the motor was pulled due to a spun bearing. The crank is good and lists for $900 new from GM.
Crank $100
Rods $40
Block $200
SBF
5.0 Heads
5.0 Cranks
351W Cranks
BBF
2 pair of 460 heads $100 ea pair
429 cranks $100
460 cranks $100
Pontiac
1 early 70s N 400 crank $200
Intakes
1 485812 $95
2 52586 $35 each
1 10003355 $40 (off of a gold s/e car)
1 9790140 $95 (72 GTO)
1 2bbl intake off a 69 GTO $20
1 2bbl intake 72 model $10
Timing covers
2 12 bolt $100 each
1 8 bolt cover $65
water pump backing plates $20 each
Angled water necks $15 each
Valley pans
shallow $20
deep $15
comp cam
P-320H-10
268/268 @ .050 .594/.594 lift w/ 1.65 110 LSA
w/ matching lifters
Hydraulic 8 1/4 passes
$75
Ported 670 D-port heads:
Over 70 hours of porting, polishing, smoothing etc.
Push rod holes clearanced for 1.65 rockers
Casting numbers removed
Standard d-port valve seats (30 degree) 3 angle valve job, surfaces have been decked and squared, true 72cc chamber size
Port openings have been matched to RA IV size, ports have been straightened up, push rod bulges knocked down and the bowls have been blended. All excess material in oil drain back passages has been removed and smoothed to aid in drain back.
Bare with Guide Plates
$600 OBO
Complete with 3/8 rockers, guideplates, 292/292 .490/.490 cam, matched springs, stock 1.5 rockers, stock valve covers and new valves, plus ARP head bolts
$700 OBO
All above plus ferrea Exhaust 1.77 X 5.230 X 45 Deg Intake
2.11 X 5.213 X 45 Deg, K-motion K1000 springs, Ti retainers and locks
$800 OBO
72 case BOP pattern TH 350
trans-go shift kit and clutches
Hardened sprag
Stock valve body still has kickdown cable
New pump
$400
1975 400 block .030 over 2 bolt main
1972 400 N crank .010/.010
Clevitte77 full groove race main bearings
Federal mogal 3/4 race rod bearings
Baffled Oil pan
Melling oil pump w/ shimmed spring.
Stock rods with arp bolts
Speed Pro cast pistons with 18cc dish giving 9.5:1 compression
Polished timing cover
stock waterpump
stock balancer
stock flexplate
Basically needs new rings, crank polished maybe turned.
$300
Ferrea 6000 Stainless Steel Valves
Exhaust
1.77 X 5.230 X 45 Deg
Intake
2.11 X 5.213 X 45 Deg
Full set, a few passes on them but are as good as new.
$150
Cometic Head Gaskets
4.160 bore
.027 thick
standard water hole and locations
New in the box never torqued just removed from orginal packaging.
$150
Several other early 400s with cranks, I will consider serious offers. Same on 455s. I also have several sets of heads, brackets, pulleys, etc.
Competition Engineering shocks Rears
for 67-69 firebird/camaro
3 way adjustable, used
$20
US body 77-81 Firebird 4" pin on hood
Lift Off hood
Dzeus fastenors
great shape has been painted red before and sanded back down
Weight is 22 lbs.
Over $400 cost new
$200 OBO
9 Inch ford rear 56" across outside tube to outside tube, housing only $50
8.8 complete explorer rear disassembled $75
1 gas tank for 71-74 ventura II, 68-74 Nova, 73-74 Omega/apollo $40
1 gas tank for 70-81 firebird/camaro $40
Front bumper cover 87-93 mustang $150
Quarter windows 87-93 mustang $300
87-93 GT tail lights $100
87-93 Hood $50
93 LX Grey front and rear seats $250
2 350 2 bolt blocks $100 apiece or $175 for both
1 350 2 bolt short block $150
1 350 4 bolt short block 1 piece rear main $225
1 350 4 bolt block $150
BBC
396 block $200
Several sets of heads $75 a pair
Gen V 454 Forged Steel crank, 6 7/16" dimple rods
the crank is std and will probably need turned as one journal is discolored and the motor was pulled due to a spun bearing. The crank is good and lists for $900 new from GM.
Crank $100
Rods $40
Block $200
SBF
5.0 Heads
5.0 Cranks
351W Cranks
BBF
2 pair of 460 heads $100 ea pair
429 cranks $100
460 cranks $100
Pontiac
1 early 70s N 400 crank $200
Intakes
1 485812 $95
2 52586 $35 each
1 10003355 $40 (off of a gold s/e car)
1 9790140 $95 (72 GTO)
1 2bbl intake off a 69 GTO $20
1 2bbl intake 72 model $10
Timing covers
2 12 bolt $100 each
1 8 bolt cover $65
water pump backing plates $20 each
Angled water necks $15 each
Valley pans
shallow $20
deep $15
comp cam
P-320H-10
268/268 @ .050 .594/.594 lift w/ 1.65 110 LSA
w/ matching lifters
Hydraulic 8 1/4 passes
$75
Ported 670 D-port heads:
Over 70 hours of porting, polishing, smoothing etc.
Push rod holes clearanced for 1.65 rockers
Casting numbers removed
Standard d-port valve seats (30 degree) 3 angle valve job, surfaces have been decked and squared, true 72cc chamber size
Port openings have been matched to RA IV size, ports have been straightened up, push rod bulges knocked down and the bowls have been blended. All excess material in oil drain back passages has been removed and smoothed to aid in drain back.
Bare with Guide Plates
$600 OBO
Complete with 3/8 rockers, guideplates, 292/292 .490/.490 cam, matched springs, stock 1.5 rockers, stock valve covers and new valves, plus ARP head bolts
$700 OBO
All above plus ferrea Exhaust 1.77 X 5.230 X 45 Deg Intake
2.11 X 5.213 X 45 Deg, K-motion K1000 springs, Ti retainers and locks
$800 OBO
72 case BOP pattern TH 350
trans-go shift kit and clutches
Hardened sprag
Stock valve body still has kickdown cable
New pump
$400
1975 400 block .030 over 2 bolt main
1972 400 N crank .010/.010
Clevitte77 full groove race main bearings
Federal mogal 3/4 race rod bearings
Baffled Oil pan
Melling oil pump w/ shimmed spring.
Stock rods with arp bolts
Speed Pro cast pistons with 18cc dish giving 9.5:1 compression
Polished timing cover
stock waterpump
stock balancer
stock flexplate
Basically needs new rings, crank polished maybe turned.
$300
Ferrea 6000 Stainless Steel Valves
Exhaust
1.77 X 5.230 X 45 Deg
Intake
2.11 X 5.213 X 45 Deg
Full set, a few passes on them but are as good as new.
$150
Cometic Head Gaskets
4.160 bore
.027 thick
standard water hole and locations
New in the box never torqued just removed from orginal packaging.
$150
Several other early 400s with cranks, I will consider serious offers. Same on 455s. I also have several sets of heads, brackets, pulleys, etc.
Competition Engineering shocks Rears
for 67-69 firebird/camaro
3 way adjustable, used
$20
US body 77-81 Firebird 4" pin on hood
Lift Off hood
Dzeus fastenors
great shape has been painted red before and sanded back down
Weight is 22 lbs.
Over $400 cost new
$200 OBO
9 Inch ford rear 56" across outside tube to outside tube, housing only $50
8.8 complete explorer rear disassembled $75
1 gas tank for 71-74 ventura II, 68-74 Nova, 73-74 Omega/apollo $40
1 gas tank for 70-81 firebird/camaro $40
Front bumper cover 87-93 mustang $150
Quarter windows 87-93 mustang $300
87-93 GT tail lights $100
87-93 Hood $50
93 LX Grey front and rear seats $250
